CVO Garage
December 18, 2018, 08:46:13 AM *
Welcome, Guest. Please login or register.

Login with username, password and session length
News: The Garage is accepting donations for upkeep and maintenance.  Click the Donations Menu Tab to help!
 
   Home   Help Login Register  
Pages: [1]   Go Down
  Print  
Author Topic: ok now i got a code  (Read 2677 times)
0 Members and 2 Guests are viewing this topic.
1badcvo
Shop Gopher
*
Offline Offline

Gender: Male
Location: plainview ny
Posts: 20





My Ride 1:2009 cvo fat bob

My Ride 2:2007 sportster 1200L

My Ride 3:2007 FXDL low rider
« on: August 05, 2010, 11:21:09 AM »

well now i got a 1371 code and i cant seem to find out what that is, figures lol been told no such code but seen it plain as day
Logged
Posty McPosterson
Administrator
Executive QC Service Advisor
*
Offline Offline

Gender: Male
Location: Western NY
Posts: 64713





My Ride 1:'07 Cherry Jester
« Reply #1 on: August 05, 2010, 12:23:37 PM »

no letter preceding the code?  Nixweiss

Here is the procedure to pull the codes.

1- Turn Ignition switch to OFF & Run/Stop switch is to Run.

2- Push odometer reset button in & hold.

3- Turn ignition switch to Ignition and release odometer reset button. Background lighting should illuminate, speedometer needle should sweep its full range and indicator lamps (battery, security, low fuel, check engine and cruise) should illuminate. The word “diag” should then appear.

4 - Push the odometer reset button once and you will see the selection menu "PSSPt" with the first P flashing.

5 - Each letter represents an area of the diagnostics module. The module that is flashing is the one you are going to check. To move from one letter (module) to the next, you push the odometer reset button one time. (from P to S to SP to t and back to P, etc.)
P = ECM/ICM (Electronic Control Module [EFI] / Ignition Control Module [Carbureted)
S = TSM/TSSM (Turn Signal/ Turn Signal Security Module)
SP = speedometer
T = tachometer

6 - To get the DTC within an area of diagnostics, push and hold the odometer reset button in for 5 seconds and release. If there are any DTC’s the code will be displayed or the word “none” will appear if there are no DTC’s. Push the odometer reset button again to view additional codes if they exist.

7 - Record the codes.

8 - If DTC’s are not to be cleared, Press and release the odometer reset button. Part number of module will be displayed.
NOTE: To determine if a code is current or historic, clear the displayed code by pushing in and holding the odometer reset button ( longer than 5 seconds) until 'clear' comes up. Release the odometer reset button. Turn OFF the ignition switch. Run your bike and shut it down then recheck the DTC’s again by repeating steps 1 to 9. If the code is current it will reappear.

9 – Press and release the odometer reset button to continue to the next module.

10 – Turn Ignition switch to OFF.

On models not equipped with a tachometer "No Rsp" will appear when the tachometer identifier is selected.

"No Rsp" will also appear if the run/off switch is in the off position when doing this procedure.

Also if the code set is a historic code (not a constant light) after 50 start and run cycles of at least 30 seconds each in duration, the light will extinguish itself as long as the error hasn't occurred again.
If it were a current code, the light would remain lit while running.
Logged

"A good wife always forgives her husband when she's wrong"
Pages: [1]   Go Up
  Print  
 
Jump to:  

Powered by MySQL Powered by PHP Powered by SMF 1.1.11 | SMF © 2006-2009, Simple Machines LLC Valid XHTML 1.0! Valid CSS!
Page created in 0.074 seconds with 19 queries.